1 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com technical data sheet 1.6mm round subminiature side looking infrared led EAISV3026A0 features ? peak wavelength p= 940 nm. ? low forward voltage. ? compatible with infrared and vapor phase reflow solder process. ? package in 8mm tape on 7 diameter reels. ? pb free ? the product itself will remain within rohs compliant version. ? compliance with eu reach. ? compliance halogen free .(br <900 ppm ,cl <900 ppm , br+cl < 1500 ppm) d escription ? EAISV3026A0 is an infrared emitting diode in miniature smd package which is molded in a water clear plastic with flat top view lens. the device is spectrally matched with silicon photodiode and phototransistor. applications ? infrared applied s ystem device selection guide device no. chip material lens color EAISV3026A0 gaalas water clear
datasheet EAISV3026A0 2 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com package dimensions notes: 1.all dimensions are in millimeters 2.to lerances unless dimensions 0.1mm absolute maximum ratings (ta=25 parameter symbol rating unit continuous forward current i f 65 ma reverse voltage v r 5 v operating temperature t opr - 40 ~ + 85 stg - 40 ~ + 100 sol 260 d 1 00 mw notes: * 1 :soldering time Q 5 seconds. recommended soldering pattern for side looker
datasheet EAISV3026A0 3 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com electro - optical characteristics (ta=25 ) parameter symbol min. typ. max. unit condition radiant intensity i e 4.0 8.0 -- mw /sr i f =20ma -- 40 -- i f =100ma pulse width Q 100 s ,duty Q 1% peak wavelength p 920 940 960 nm i f = 10 0ma spectral bandwidth ? -- 30 -- nm i f = 10 0ma forward voltage v f -- 1.25 1.50 v i f =20ma -- 1.40 1.80 i f =100ma pulse width Q 100 s ,duty Q 1% reverse current i r -- -- 10 a v r =5v view angle 2 1/2 -- 20 -- deg i f =20ma
datasheet EAISV3026A0 4 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com typical electrical/optical/characteristics curves forward current vs. ambient temperature spectral distribution relative intensity vs. forward current relative intensity vs. forward current 0 5 10 15 20 25 30 35 40 45 50 55 60 65 0 5 10 15 20 25 30 radiant intensity(mw/sr) forward current(ma) 0 1 2 3 4 5 10 1 10 2 10 3 10 4 tp=100us tp/t=1/100 forward current(ma) forward voltage(v) 0 20 40 60 80 100 0 20 40 60 80 100 t amb - ambient temperature (c) i f - forward current (ma) 700 725 750 775 800 825 850 875 900 925 950 975 1000 1025 1050 0.0 0.2 0.4 0.6 0.8 1.0 relative radinat intensity (%) wavelength (nm)
datasheet EAISV3026A0 5 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com relative radi ant intensity vs. angular displacement 0 30 60 90 -90 -60 -30 0 0.0 0.2 0.4 0.6 0.8 1.0 reletive radiant intensity view angle(degree)
datasheet EAISV3026A0 6 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com precautions for use 1. over - current - proof customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( burn out will happen ). 2. storage 2.1 do not open moist ure proof bag before the products are ready to use. 2.2 before opening the package, the leds should be kept at 30 or l ess and 6 0%rh or less. 2. 3 the leds should be used within a year. 2. 4 after opening the package, the leds should be kept at 30 or less and 6 0%rh or less. 2.5 the leds should be used within 168 hours (7 days) after opening the package 2.6 if the moisture absorbent material (silica gel) has faded away or the leds have exceeded the storage time, baking treatment should be performed using the following conditions. baking treatment : 60 5 for min. 24 hours. 3. soldering condition 3.1 pb - free solder temperature profile 3.2 reflow soldering should not be done more than two times. 3.3 when soldering, do not put stress on the l eds during heating. 3.4 after soldering, do not warp the circuit board.
datasheet EAISV3026A0 7 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com 4. soldering iron each terminal is to go to the tip of soldering iron temperature less than 350 for 3 seconds within once in less than the soldering iron capacity 25w. leave two seconds and more intervals, and do soldering of each terminal. be careful because the damage of the product is often started at the time of the hand solder. 5. repairing repair should not be done after the leds have been soldered. when repairing is unav oidable, a double - head soldering iron should be used (as below figure). it should be confirmed beforehand whether the characteristics of the leds will or will not be damaged by repairing.
datasheet EAISV3026A0 8 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com package dimensions note: th e tolerances unless mentioned is 0.1mm ,unit = mm carrier tape dimensions: (q uantity : 15 00 pcs/ reel ) note: the tolerances unless mentioned is 0.1mm ,unit = mm
datasheet EAISV3026A0 9 copyright ? 2010, everlight all ri ghts reserved. release date : jan . 0 6 .201 7 . issue no: dir - 0001635 rev.2 www.everlight.com packing procedure label form specification cpn: cus tomers production number p/n : production number qty: packing quantity cat: ranks hue: peak wavelength ref: reference lot no: lot number made in taiwan: production place disclaimer 1. everlight reserves the right(s) on the adjustment of product material mix for the specification. 2. the product meets everlight published specification for a period of twelve (12) months from date of shipment. 3. the graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. when using thi s product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. everlight assumes no responsibility for any damage resulting from the use of the product which does not comply with the absolute m aximum ratings and the instructions included in these specification sheets. 5. these specification sheets include materials protected under copyright of everlight . reproduction in any form is prohibited without obtaining everlight s prior consent. 6. this produc t is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. please contact authorized e verlight sales agent for special applicatio n request. aluminum moistue-proof bag label desiccant label xxxxxxxxxxxxxxxxxxxx xxxxxxxxxx xxxxxxxxxx - xxxxxxxxxx - xxxxxxxxxx xxxxxxxxxx xxxxxxxxxx btpyymmddxxxxx made in xxxxxx msl - x x
|
